There isn't a way to surface mount the Optronics clearance light part # STL175AMFB so best option would be to go with a similar light that can be surface mounted like the Miro Flex part # OPT78FR. view full answer...
The brake controller install harness you need to install the Tekonsha Primus IQ part # TK90160 in your 2018 Ford E-450 is the part # 3040-P.
The brake controller plug will be located behind the dash in one of two places, as you can see in the photos I've provided. view full answer...
Wiring adapter # 22292 is the correct one for installing a Tekonsha brake controller such as the Prodigy P3 # 90195 in your Ford F-450 cab and chassis.
There are two possibilities you can check to troubleshoot this issue. First, use a circuit tester like # PTW2992 to confirm that the connector under your dash has one pin with constant 12V power and one with 12V power ONLY when the brake is pressed. The other two pins should not carry any voltage. If your vehicle connector displays different... view full answer...
For a 10 foot awning for the Ford van you have that was converted to an ambulance you'd want a wall mounted awning like the Thule Hideaway Awning part # TH4900011. view full answer...
I have a couple of options for hitches for your 2001 Ford F-450 cab and chassis depending on whether or not you want a 2" receiver or a 2-1/2" receiver. I have listed both options below:
2" Hitch - Curt Trailer Hitch Receiver item # C15445
2-1/2" Hitch - Curt Trailer Hitch Receiver item # C15845
If you are wanting a hitch that has both a 2" and a 2-1/2" receiver then you will need the TorkLift SuperHitch Original Trailer Hitch Receiver item # TLF1003. view full answer...
A rear sway bar for your 2017 Thor Class C built on a Ford F-450 chassis like the part # RM-1139-147 would make the biggest improvement in handling and stability. Next a front sway bar like part # RM-1139-176 would be a great option as well. view full answer...
For your 2016 Ford F-450 Cab and Chassis, the Edge Stage 1 Performance Kit w/ Diesel Evolution CS2 Programmer and Jammer Air Intake, # EP19003, you asked about has 3 settings to increase horsepower and torque. Setting 1 will give you an additional 39 hp and 73 lbs torque to your factory settings. Setting 2 will give you 73 hp and 153 lbs torque. Setting 3 will give you 109 hp and 234 lbs torque. This system is not legal in California.
For a dash board mounted backup camera system,... view full answer...
Doing some research on your 2017 Jayco Redhawk, it looks like it has a Ford E-450 chassis. If that is the case, then we do offer some custom fit floor mat options that will work great.
For the best option that complements all interior colors, I recommend the WeatherTech Front Auto Floor Mats # WT26DV. These black mats are custom-designed to fit the exact contours of your vehicle. Also, the mats come with the WeatherTech lifetime warranty and are 100% made in the U.S.A.
To keep the mats... view full answer...
The Adco Olefin HD RV Cover # AD34ZR is a great option for your 2018 Jayco 26XD Class C RV. This cover works best for long-term storage in all climates. Heavy-duty fabric protects against rain, dirt, wind, and sun. The contoured fit will match shape of your RV and secure with cinch ropes and straps for nice, snug fit. view full answer...
The Valterra RV Water Tank # R8048 can be installed standing up for laying down as is demonstrated in the 2 attached photos.
If you have it oriented so that it sits taller the drain plug will already be in a position to drain properly. Should you choose to mount it so that it has a lower profile you will simply need to use one of the pre-drilled holes as a drain. If you finish drilling them through to the tank you will be able to use them as a drain as you can see in the attached picture... view full answer...
The correct front mount trailer hitch for a 2016 Freedom Elite Motorhome on Ford E-450 Cutaway Chassis is the Draw-Tite Front Mount Trailer Hitch Receiver part # 65053. This is the only available option for this chassis.
It seems like you were looking at front mount hitches for a F-Series and not the E-Series which is where the confusion lies. view full answer...
For your 2019 Ford E-450 Cutaway, I recommend using WeatherTech All-Weather Front Floor Mats part # WTW51 for black, part # WTW51GR for gray, or part # WTW51TN for tan. Like you said, the manufacturer does not recommend using these or the thermoplastic option because you have the vinyl flooring. These recommendations are ruber, and not thermoplastic.
The above floor mats are all custom fit options which means they are contoured specifically to match the footwell in your cutaway. I have... view full answer...
If your motorhome has the 2015 Ford F-450 cab and chassis that you input for your vehicle info then the Wiring Adapter # C51436 is the problem. You should actually be using the Wiring Adapter # C51432 for your TriFlex # C24VV instead.
When I spoke with my contact at Curt he said that for the Ford pickups if the wrong adapter is used then it does something to the anti-theft and keeps the vehicle from starting. view full answer...
There were a few different wheel and tire options on the 2012 Ford E450 Chassis so I can't tell you for sure but I can help you identify what you have and help find a match for it for you.
The information we need to determine the correct spare is on the tire. The side wall will have the sizing information we are looking for. The Provider ST235/80R16 Trailer Tire w/ 16" Silver Dual Wheel part # TA95FR that you looked at is a 235/80R16 sized tire and is Load Range E. Confirm that this matches... view full answer...
I think the best option to help illuminate the instrument panel better in the daytime would be to take some LED strips like part # UCL90CB and line the top or bottom of the bezel which holds the instrument panel. This could then be wired to an on/off switch so you can turn them off at night. It would also provide you with plenty of extra light to illuminate other areas of the motorhome such as inside a cabinet or under the dash in the foot well area. view full answer...
I looked up your 2017 Thor Windsport Coach and it uses a single pull out step just like the Kwikee 28 Series part # LC3747453 that you referenced so this would easily replace what you have and work well. It will pull out automatically when you open the door and retract when you close it. view full answer...
For your 2018 Forest River Forester 3051 Class C that is built on a E-450 chassis we have the Roadmaster front sway bar part # RM-1139-179 which is a confirmed fit but we do not have a rear bar. view full answer...
For a 2018 Jayco Greyhawk 26Y on a Ford E-450 chassis you would need the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets # RM47MR. This stabilizer is a simple bolt-on design with no drilling required.
If you don't already have a rear sway bar then I recommend installing the Roadmaster # RM-1139-147 as well. If your front anti-sway bar is less than 1-3/8" thick then you can beef it up with the # RM-1139-189 as well. view full answer...
I checked with Roadmaster and for your 1997 Tioga Montara built on a Ford E-450 chassis the correct sway bars are the part # RM-1139-147 for the rear like you mentioned and then for the front part # RM-1139-115. view full answer...
Go To Results